|
|
|
|
Strumenti |
23-02-2021, 17:58 | #1 |
Senior Member
Iscritto dal: Jun 2002
Città: Marte
Messaggi: 1052
|
HDD Seagate afflitto da bsy bug Firmware flash
Ciao a tutti ho l'hhd seagate ST3500620AS con firmware HP24 al quale e stato rilasciato il suo correttivo HP sp52107 . Sfortunatamente non capisco come flashiare l'hdd HP26 nonostante abbia a disposizione i file per il flash. Ringrazio chiunque possa aiutarmi.
Ciao a tutti
__________________
Il Milanese Imbruttito Ultima modifica di Teils : 23-02-2021 alle 19:53. |
24-02-2021, 09:51 | #2 | |
Senior Member
Iscritto dal: Mar 2008
Messaggi: 18074
|
Quote:
INSTALLATION INSTRUCTIONS: NOTE: It is STRONGLY recommended that you perform a system backup prior to installing this update. 1. Download the file by clicking the "Download" or "Obtain Software" button and saving the file to a folder on your hard drive (make a note of the folder where the downloaded file is saved). 2. Double-click the downloaded file and follow the on-screen instructions. 3. This HP26 firmware does not support (boot time) ATA Drive Lock Password Protection. If you have a Drive Lock Password set you will need to disable the password before downloading the new firmware. If you try to download firmware when the drive is locked, the firmware download will abort. Once this firmware is installed, the drive will no longer support Drivelock Password protection. To perform the update: 1. Boot the target system to your DOS-bootable USB key. 2. Change to the folder containing the utility files and execute the appropriate .BAT file. The utility will skip any drives that are not targets. It only updates drives that have the affected model string. It will re-update target drives that already have the correct firmware but no harm is done in that. 3. When all drives have been updated, you must POWER CYCLE the system to ensure that the drives are fully updated. Chiaramente visto la delicatezza dell'operazione è meglio leggere tutto il documento, per intero. Riscrivo il link sperando che stavolta il forum lo faccia vedere a tutti e non solo a chi replica... ftp://ftp.hp.com/pub/softpaq/sp52001-52500/sp52107.html |
|
24-02-2021, 20:57 | #3 |
Senior Member
Iscritto dal: Jun 2002
Città: Marte
Messaggi: 1052
|
Ma non ho capito se devo per forza disporre di quella workstation ho posso aggiornarlo da qualsiasi pc
TITOLO: Aggiornamento del firmware del disco rigido SATA Seagate Barracuda 7200.11 per HP Postazioni di lavoro VERSIONE: HP26 Rev. B DESCRIZIONE: Questo pacchetto fornisce un'utilità per aggiornare il firmware su alcuni serial ATA (SATA) dischi rigidi (HDD) per i modelli di workstation supportati e operativi sistemi. L'aggiornamento del firmware fornisce una correzione preventiva del firmware per un noto problema. L'utilità inclusa in questo pacchetto aggiorna il firmware di seguito Dischi rigidi SATA da 7200 rpm Seagate forniti su workstation HP: Numero modello Seagate: Numero parte HP: ST3500620AS 461123-001 ST750630AS 460315-002 ST31000340AS 464263-001 Revisione firmware: da HP12 a HP24 NOTA: le utilità incluse verificano che sia presente un modello di disco rigido interessato viene installato prima di aggiornare il firmware. Se il modello di disco rigido corretto è non trovato, il firmware non è aggiornato. Il nuovo firmware risolve un problema ben pubblicizzato che potrebbe rendere l'unità inutilizzabile dopo un ciclo di alimentazione. Sebbene le possibilità di guasto di un'unità siano minimo, HP consiglia di aggiornare tutti i dischi rigidi appropriati come file misura preventiva. Dopo l'aggiornamento, la revisione del firmware sarà HP26. L'utilità inclusa crea una chiave USB avviabile DOS che conterrà tutti i file file per aggiornare i dischi rigidi identificati. Per creare o modificare il supporto di avvio, seguire le istruzioni in File MAKEIT.TXT, che si trova nel livello superiore della cartella installata albero. SCOPO: Consigliato NUMERO SOFTPAQ: SP52107 SUPERSEDE: Nessuno DATA DI ENTRATA IN VIGORE: 14 marzo 2011 CATEGORIA: Firmware SSM SUPPORTATO: No TIPO DI PRODOTTO: Postazioni di lavoro MODELLO / I PRODOTTO HARDWARE: Workstation brasiliana HP xw4600: tutti i modelli Workstation HP xw4400: tutti i modelli Workstation HP xw4600: tutti i modelli Workstation HP xw6400: tutti i modelli Workstation HP xw6600: tutti i modelli Workstation HP xw8400: tutti i modelli Workstation HP xw8600: tutti i modelli Workstation HP xw9400: tutti i modelli Workstation HP Z400: tutti i modelli Workstation brasiliana HP Z600: tutti i modelli Workstation HP Z600: tutti i modelli Workstation HP Z800: tutti i modelli PRODOTTO (I) SOFTWARE: Nessuna SISTEMI OPERATIVI): DOS gratuito Microsoft Windows 7 a 32 bit Enterprise Microsoft Windows 7 a 32 bit Professional Microsoft Windows 7 a 64 bit Enterprise Microsoft Windows 7 64 bit Professional Microsoft Windows Vista Business 32 Edition Microsoft Windows Vista Business 64 Edition Microsoft Windows XP Professional Microsoft Windows XP Professional x64 Edition Red Hat Ent Linux 4 (x86) Red Hat Enterprise Linux 3 (x86) Red Hat Enterprise Linux 5 Desktop (x86) SUSE Linux Enterprise Desktop 11 (x86) LE LINGUE): Globale MIGLIORAMENTI: N / A CORREZIONI: - Risolve un problema noto relativo allo stato del registro eventi critici dell'unità in quel momento di un ciclo di alimentazione. - Risolve un problema che può causare un messaggio di errore del disco o del disco non di sistema in tempo di avvio. - Disabilita la scansione offline aggressiva. PREREQUISITI: NOTA: l'utilità di aggiornamento del firmware non può aggiornare le unità che sono membri di Array RAID. Tuttavia, è possibile rimuovere temporaneamente il sistema dal RAID modalità, eseguire l'aggiornamento sulle unità di destinazione, quindi ripristinare il sistema in modalità RAID. Perché l'aggiornamento del firmware non influisce sul contenuto dei dati delle unità, inclusi i dati di appartenenza RAID, l'array funzionerà normalmente quando viene ripristinata la modalità RAID. In tutte le workstation supportate modelli per questo aggiornamento, la modalità controller SATA può essere gestita tramite le opzioni in l'interfaccia di configurazione del BIOS F10. Per istruzioni specifiche, vedere il manuale per il tuo modello di computer. Questa modalità di gestione NON comporta l'eliminazione o la creazione Array RAID. NOTA: quando si utilizza il metodo della chiave USB sulla workstation HP xw9400, lo è necessario disabilitare la ROM opzionale SATA per consentire all'utility eseguire correttamente la scansione del bus SATA. Alcune di queste modifiche temporanee riducono l'estensione numero di porte SATA attive. Se sono presenti molti dischi rigidi di destinazione, potrebbero devono essere temporaneamente collegati a porte inferiori per l'aggiornamento. - 2 MB di spazio libero sono necessari sul sistema su cui verrà installato il SoftPaq scaricato. - Una chiave USB avviabile con almeno 1,1 MB di spazio libero o una chiave USB che può essere riformattato è necessario. ISTRUZIONI PER L'INSTALLAZIONE: NOTA: Si consiglia VIVAMENTE di eseguire un backup del sistema prima di l'installazione di questo aggiornamento. 1. Scarica il file facendo clic sul pulsante "Download" o "Ottieni software" e salvare il file in una cartella sul disco rigido (prendere nota della cartella in cui il file scaricato viene salvato). 2. Fare doppio clic sul file scaricato e seguire le istruzioni sullo schermo. 3. Questo firmware HP26 non supporta (all'avvio) la password di blocco unità ATA Protezione. Se hai impostato una password per il blocco dell'unità, dovrai disabilitare il file password prima di scaricare il nuovo firmware. Se provi a scaricare il firmware quando l'unità è bloccata, il download del firmware verrà interrotto. Una volta che questo firmware è installato, l'unità non supporterà più la protezione con password di Drivelock. Per eseguire l'aggiornamento: 1. Avvia il sistema di destinazione
__________________
Il Milanese Imbruttito |
25-02-2021, 15:29 | #4 |
Senior Member
Iscritto dal: Mar 2008
Messaggi: 18074
|
A questo purtroppo no so rispondere con certezza, ma devo immaginare che se l'aggiornamento è possibile effettuarlo solo col disco montato sulle workstation specificate, il programmatore abbia previsto un check in tal senso e il programma non effettui l'aggiornamento su altre macchine.
|
25-02-2021, 17:20 | #5 |
Senior Member
Iscritto dal: Jun 2002
Città: Marte
Messaggi: 1052
|
l'hdd e proprio quello pero non ho la workstation in questione
__________________
Il Milanese Imbruttito |
25-02-2021, 18:52 | #6 |
Senior Member
Iscritto dal: Mar 2008
Messaggi: 18074
|
Comprendo, ma temo che non hai molte scelte. Lasci tutto com'è bug compresi o ti avventuri per l'aggiornamento del firmware. Chiaramente un backup delle cose che non intendi perdere è obbligatorio, come del resto consigliato dallo stesso produttore del firmware.
|
26-02-2021, 01:04 | #7 |
Senior Member
Iscritto dal: Aug 2018
Città: Verona
Messaggi: 1025
|
Se l'hdd si trova già in stato busy, non sarà possibile aggiornare in alcun modo il firmware finchè non verrà sbloccato a livello terminal.
L'aggiornamento è possibile solo se si presenta in stato "ready" (quindi non più busy). L'aggiornamento serve per impedire che il problema si ripresenti, ma non è la soluzione quando l'hdd è già bloccato in stato busy. |
26-02-2021, 10:49 | #8 | |
Senior Member
Iscritto dal: Jun 2002
Città: Marte
Messaggi: 1052
|
So che l'hdd in stato busy non è aggiornabile ovviamente perchè non viene riconosciuto nemmeno dalla scheda madre infatti ho comprato il kit per farlo uscire dalla modale busy e adeso e visto dal pc e parte anche il sistema operativo.
Quote:
__________________
Il Milanese Imbruttito |
|
27-02-2021, 20:37 | #9 | |
Senior Member
Iscritto dal: Jun 2002
Città: Marte
Messaggi: 1052
|
Quindi come dovrei fare per aggiornarlo essendo in stato ready?
Quote:
__________________
Il Milanese Imbruttito |
|
01-03-2021, 22:00 | #10 |
Senior Member
Iscritto dal: Aug 2018
Città: Verona
Messaggi: 1025
|
Va aggiornato dal DOS puro (quindi non col CMD di windows).
Hai estratto i files dal SP52107.exe ? Puoi fare tasto destro sul file che hai scaricato ed estrarre il contenuto con Winrar. Poi segui le istruzioni contenute nel file "MAKEIT.txt" ... che riporto direttamente qui sotto: Codice HTML:
This update requires you to reboot the machine that has hard drives to be updated into the DOS operating system from a bootable USB-Key drive. =====Format USB-Key as Bootable method===== Note that this is a two-step process: a) First, the USB-Key must be formatted as a DOS-boot device, unless you already have a key set up that way. b) Then, the utility and other files must be copied to the USB-Key. Format the USB-Key (if needed): 1) Using Microsoft Windows Explorer, navigate to the directory where you installed this update (the default installation directory is C:\swsetup\#####). 2) Double-click HPUSBFormatter.exe and follow the on-screen instructions to install the application. 3) Insert your USB-Key. 4) ***IMPORTANT***: Back up any important files from your USB-Key at this time. You will need to format your USB-Key in the next few steps, thereby destroying any data on your USB-Key. 5) From the Start menu, choose Programs, Hewlett-Packard Company, HP USB Disk Storage Format Tool. 6) Choose your device from the drop-down menu. Ensure that "FAT" is selected. Choose to "Create a DOS startup disk," "using DOS system files located at C:\swsetup\#####\usb_files\. 7) Start the format. 8) After the format is complete, close the HP USB Disk Storage Format Tool program. Copy the utility and other files to the USB-Key: 1) Using Microsoft Windows Explorer, navigate to My Computer. 2) Note the drive letter of the recently formatted USB-Key (for example: F:). 4) Using Microsoft Windows Explorer, return to C:\swsetup\#####\. 5) Navigate to the usb_files\ directory. 6) Select ALL files in this directory. From the menubar, choose Edit > Copy. 7) Using Microsoft Windows Explorer, navigate to the recently formatted USB-Key (for example: F:). From the menubar, choose Edit > Paste, to paste the files onto the USB-Key at the root folder level. Select Yes to All for file overwrites. Your USB-Key is now ready. Now follow the instructions in "Performing the Update," which appears later in this document. =====Use an Existing USB-key===== This method assumes you already have the DOS operating system on a bootable USB-key and only need to copy the utility and other files to the key. In this case, the files are copied to a sub-folder in order to avoid overwriting any of the DOS files at the root folder of your bootable medium. The utility files may be large, so be sure they will fit on your USB-key before starting the copy. Note that HP testing is only done with the version of DOS created by the other methods described in this file. HP cannot be responsible for issues associated with the DOS you already have, so if you encounter trouble, consider trying one of the other methods. 1) Insert your USB-Key into a port on the system where you unpacked this update. 2) Using Microsoft Windows Explorer, navigate to My Computer. 3) Note the drive letter of the USB-Key (for example: F:) 4) Using Microsoft Windows Explorer, navigate to the directory where you installed this update (the default installation directory is C:\swsetup\#####). 5) Right-click the usb_files\ directory and select Copy. 6) Using Microsoft Windows Explorer, navigate to the USB-Key (for example, F:. 7) From the menubar, choose Edit > Paste, to paste the usb_files\ folder onto the medium. (If you already had a folder with that name, you'll have some renaming to do.) WARNING: The usb_files\ folder contains DOS system files; be careful not to paste them at the root of your bootable medium!! Your USB-Key is now ready. Now follow the instructions in "Performing the Update," which appears later in this document. =====Performing the Update===== NOTE: It is STRONGLY recommended that you perform a system backup prior to installing this update. NOTE: The firmware update utility cannot upgrade drives that are members of RAID arrays. However, it is possible to temporarily take the system out of RAID mode, perform the upgrade on the target drives, and then put the system back into RAID mode. Because the firmware upgrade does not affect the data contents of the drives, including their RAID membership data, the array will operate normally when the RAID mode is restored. In all the supported workstation models for this update, the SATA controller mode can be managed via options in the BIOS F10 Setup interface. For specific instructions, see the manual for your computer model. This mode management does NOT involve deleting or creating RAID arrays. NOTE: When using the USB key method on the HP Workstation xw9400, it is necessary to disable the SATA Option ROM in order for the utility to successfully scan the SATA bus. Some of these temporary changes reduce the number of active SATA ports. If many target hard drives are present, they may need to be temporarily connected to lower ports for the upgrade. Once you've created your DOS bootable USB-key, follow these steps: 1. Boot the target system to your DOS-bootable USB-key. 2. Change to the folder containing the utility files, and execute the HP26CE3D.BAT script. The utility will skip any drives that are not targets. It only updates drives that have the affected model string. It will re-update target drives that already have the correct firmware but no harm is done in that. 3. When all drives have been updated, power cycle the system. It's important to do a complete power cycle to ensure that the drives are fully updated. Ormai è da circa 10 anni che non aggiorno più il fw di questi hdd con le utility ufficiali, in quelle rare volte che mi capita di dover aggiornare il fw di questi seagate lo faccio usando strumentazione professionale, quindi non ricordo benissimo come facevo. Quello che ricordo ad esempio, che non mi sembra venga menzionato nelle istruzioni in inglese" è che il bios deve essere impostato in IDE mode (Legacy mode), se è impostato in AHCI o in RAID non funzionerà. Inoltre non tutte le porte sata sono abilitate per fare l'update, cioè devi collegare l'hdd ad un canale sata di tipo 2.0 Ultima modifica di HDDaMa : 01-03-2021 alle 22:16. |
14-03-2021, 18:44 | #11 |
Senior Member
Iscritto dal: Jun 2002
Città: Marte
Messaggi: 1052
|
Cambiando pc sono riuscito ad eseguire l'upgrade
__________________
Il Milanese Imbruttito |
14-03-2021, 18:46 | #12 | |
Senior Member
Iscritto dal: Jun 2002
Città: Marte
Messaggi: 1052
|
Quote:
__________________
Il Milanese Imbruttito |
|
14-03-2021, 20:39 | #13 | |
Senior Member
Iscritto dal: Aug 2018
Città: Verona
Messaggi: 1025
|
Quote:
Non è certo uno strumento che può acquistare l'utente finale, nel senso che sarebbe troppo costoso da acquistare per fare un aggiornamento del fw o anche un semplice recupero dati del proprio hdd guasto. Ha senso acquistarlo se poi si ha un ritorno del denaro speso, cioè se lo si usa di mestiere. Ultima modifica di HDDaMa : 14-03-2021 alle 23:23. |
|
Strumenti | |
|
|
Tutti gli orari sono GMT +1. Ora sono le: 16:46.