|
|
|
|
Strumenti |
30-06-2005, 10:29 | #1 |
Member
Iscritto dal: May 2004
Città: a Roma
Messaggi: 99
|
[nic & stampante] Mandare10 problemi alla nic & stampante
Già!
Contento per l'installazione completa e senza alcun bisogno di aggiuntivi driver mi sono installato mandrake 10 sull'altro pc, quello "anzianotto" (athlon 700 con 256 di ram, 20 gb hd, nic..) ora però non mi fa accedere alla rete, la lucetta della nic è spenta e compare sulle Icon tray in basso a dx due cavetti scollegati. come posso fare? sul floppy della nic ho questi dati: LCS-8038 TX LAN Driver, ma suppongo siano per Winzozz. La marca è Longshine. Altra cosa: la stampante Canon s200 viene correttamente riconosciuta, ma provando a stampare un comunissimo file di testo per provare rimane immobile.
__________________
PiccoloSocrate Blog is here |
30-06-2005, 11:38 | #2 |
Member
Iscritto dal: May 2004
Città: a Roma
Messaggi: 99
|
un amico m'ha trovato questi driver (aveva la stessa scheda mia) sul file di help c'era questo: Codice:
RTL8139 driver(written by Donald Becker) is distributed with Linux after kernel version 2.0.34. It is better to build it into kernel. The procedure to activate rtl8139 on linux if not build in kernel: step 1: ftp the latest driver from ftp://cesdis.gsfc.nasa.gov/pub/linux/drivers/rtl8139.c step 2: compile: The instruction for compiling the driver is include at the end of the driver file. (run this instruction at /usr/src/linux) step 3: insert the driver as module: insmod rtl8139.o parameter can be added by adding options=..... behind the istrruction 0x16(bit 4):full duplex bit 0-3 :default port (run 'lsmod' to see if the module is inserted) step 4: bind your card to an IP address /sbin/ifconfig eth0 ${IPADDR} broadcast ${BROADCAST} netmask ${NETMASK} (run 'netstat -i' to see if there is a interface 'ne0') step 5: add your card to IP routing table, then add gateway also your card: /sbin/route add -net ${NETWORK} netmask ${NETMASK} eth0 (should be able to ping local network now) gateway: /sbin/route add default gw ${GATEWAY} netmask 0.0.0.0 metric 1 step 6: start inet deamon. /usr/sbin/inetd (you are on the network now) *make sure that your kernel is built with network, fast_ethernet and module support. Otherwise, you have to rebuild your kernel. (1:go to /usr/src/linux directory 2:run 'make menuconfig' or 'make config' 3:mark the options list above. 4:exit and rebuild your kernel. make dep;make clean;make zImage the file 'zImage' will be at /usr/src/linux/arch/i386/boot/zImage 5:modify /etc/lilo.conf.(this file specify where kernel image is) 6:run 'lilo' ) You cna run 'netconfig' which will do step 4,5,6 for you. This will create '/etc/rc.d/inet1' and 'inet2' files. These two files will run at boot time. Then just add a line at the beginning of 'inet1'. 'insmod /your driver'path/rtl8139.o' then your driver will work every time you boot.
__________________
PiccoloSocrate Blog is here |
30-06-2005, 11:43 | #3 |
Senior Member
Iscritto dal: Apr 2000
Città: Roma
Messaggi: 15625
|
Quel driver è incluso nel kernel da parecchi anni.
Puoi allegare i messaggi del kernel? Li ottieni col comando "dmesg" (esegui dmesg > messaggi.txt per reindirizzarli su un file di testo).
__________________
0: or %edi, %ecx; adc %eax, (%edx); popf; je 0b-22; pop %ebx; fadds 0x56(%ecx); lds 0x56(%ebx), %esp; mov %al, %al andeqs pc, r1, #147456; blpl 0xff8dd280; ldrgtb r4, [r6, #-472]; addgt r5, r8, r3, ror #12 |
30-06-2005, 12:28 | #4 |
Member
Iscritto dal: May 2004
Città: a Roma
Messaggi: 99
|
dmesg > messaggi.txt
l'ho fatto appena avviato.. poi ho provato a configurare con ip, subnet mask, gateway.. ma niente. la nic dietro nn s'accende altra cosa: nel centro di controllo ho preso questi dati per la nic id marca: 4332 dispositivo: 33081 modulo: 8139too come possono essermi utili? ci posso rintracciare dei driver utili? Grazie mille!
__________________
PiccoloSocrate Blog is here |
30-06-2005, 12:30 | #5 | |
Senior Member
Iscritto dal: Apr 2000
Città: Roma
Messaggi: 15625
|
Quote:
__________________
0: or %edi, %ecx; adc %eax, (%edx); popf; je 0b-22; pop %ebx; fadds 0x56(%ecx); lds 0x56(%ebx), %esp; mov %al, %al andeqs pc, r1, #147456; blpl 0xff8dd280; ldrgtb r4, [r6, #-472]; addgt r5, r8, r3, ror #12 |
|
Strumenti | |
|
|
Tutti gli orari sono GMT +1. Ora sono le: 15:53.