[GeeXboX 3 ] non funziona WiFi

[asghan]

Ciao
ho da poco installato geexbox-3.1-i386.iso
funziona quasi tutto eccetto la cosa che mi interessa di più il WiFi

sto usando questa scheda usb Bus 001 Device 004: ID 0bda:8176 Realtek Semiconductor Corp. RTL8188CUS 802.11n WLAN Adapter

#ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:1048 errors:0 dropped:0 overruns:0 frame:0
TX packets:1048 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:78584 (76.7 KiB) TX bytes:78584 (76.7 KiB)

wlan0 Link encap:Ethernet HWaddr XX:XX:XX:XX:XX:XX
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

ho provato piu volte ha modificare il file /etc/network ma non è cambiato niente
# Network configuration

# Backend software to use for network management (e.g. "connman")
NETWORK_BACKEND="connman"
#NETWORK_BACKEND="udhcpc"

# "LAN" or "WLAN" or "" (default is "" <--> "LAN")
NETWORK="WLAN"

# Network interface name or address (e.g. "eth0" or "00:0d:56:ec:ba:0c")
IFACE="wlan0"

# Static IP address ("" for DHCP) in CIDR format (e.g. "192.168.1.1/24")
ADDRESS="192.168.1.200"

# Network gateway (e.g. "192.168.1.254")
GATEWAY="192.168.1.1"

# List of DNS servers (e.g. "192.168.1.253 192.168.1.254")
# This will override the DNS servers from DHCP
DNS_SERVER="192.168.1.1"

SSID="**********"

# "true" or ""
HIDDEN="true"

# "WEP" or "PSK" or "" or "RSN"
SECURITY="WPA"

PASSPHRASE="**********"

# set to "" to disable NTP
TIMESERVERS="0.geexbox.pool.ntp.org 1.geexbox.pool.ntp.org 2.geexbox.pool.ntp.org 3.geexbox.pool.ntp.org"

# Services to be started at boot time
TELNET_SERVER="true"
FTP_SERVER="true"
HTTP_SERVER="false"
SAMBA_SERVER="false"

# Use Zeroconf service discovery
ZEROCONF="true"

# Static Samba shares can be defined as shown in the commented examples below,
# where <%>,<@>,<&>,<#> field separators must be present as shown (Note that
# the password cannot contain these special delimiters):

#STATIC_SMB="username<%>password<@>ip<&>myservername<#>share1<#>share2<#>share3"
#STATIC_SMB="<%><@>ip<&>myservername<#>share1"

WAIT_FOR_SLOW_DEVICE="true"


La lan funziona perfettamente ma senza il wifi non mi serve a niente

qualsiasi suggerimento è gradito :)
grazie

[sacarde]

caricato il modulo: rtl8192cu

e il firmware: firmware-realtek

?

[asghan]

penso di si

Module Size Used by Tainted: G
ppdev 4806 0
rtl8192cu 57670 0
bttv 93399 0
rtlwifi 58147 1 rtl8192cu
rtl8192c_common 31882 1 rtl8192cu
tveeprom 10799 1 bttv
mac80211 218703 2 rtl8192cu,rtlwifi
btcx_risc 2829 1 bttv
radeon 723962 4
videobuf_dma_sg 6578 1 bttv
cfg80211 163030 2 rtlwifi,mac80211
videobuf_core 13171 2 bttv,videobuf_dma_sg
rfkill 7145 3 cfg80211
v4l2_common 6204 1 bttv
videodev 74477 2 bttv,v4l2_common
drm_kms_helper 23578 1 radeon
snd_intel8x0 21601 0
rc_core 9931 1 bttv
k8temp 2569 0
ttm 43021 1 radeon
snd_ac97_codec 78459 1 snd_intel8x0
ac97_bus 704 1 snd_ac97_codec
firewire_ohci 25841 0
snd_pcm 53729 2 snd_intel8x0,snd_ac97_codec
shpchp 20447 0
firewire_core 39541 1 firewire_ohci
snd_page_alloc 5728 2 snd_intel8x0,snd_pcm
snd_timer 13512 1 snd_pcm
snd 41263 4 snd_intel8x0,snd_ac97_codec,snd_pcm,snd_timer
soundcore 4070 1 snd
parport_pc 21053 0
parport 24513 2 ppdev,parport_pc
i2c_nforce2 4459 0
vboxvideo 1295 0
drm 177368 7 radeon,drm_kms_helper,ttm,vboxvideo


se la levo o poi rimetto
............
................................................
[ 4.680218] rtl8192cu: Chip version 0x10
[ 4.687463] [drm] radeon: ring at 0x00000000A0001000
[ 4.687491] [drm] ring test succeeded in 1 usecs
[ 4.687625] [drm] ib test succeeded in 0 usecs
[ 4.687852] [drm] Radeon Display Connectors
[ 4.687854] [drm] Connector 0:
[ 4.687856] [drm] VGA-1
[ 4.687859] [drm] DDC: 0x60 0x60 0x60 0x60 0x60 0x60 0x60 0x60
[ 4.687861] [drm] Encoders:
[ 4.687863] [drm] CRT1: INTERNAL_DAC1
[ 4.687864] [drm] Connector 1:
[ 4.687866] [drm] DVI-I-1
[ 4.687868] [drm] HPD1
[ 4.687871] [drm] DDC: 0x64 0x64 0x64 0x64 0x64 0x64 0x64 0x64
[ 4.687872] [drm] Encoders:
[ 4.687874] [drm] CRT2: INTERNAL_DAC2
[ 4.687875] [drm] DFP1: INTERNAL_TMDS1
[ 4.687877] [drm] Connector 2:
[ 4.687879] [drm] SVIDEO-1
[ 4.687880] [drm] Encoders:
[ 4.687882] [drm] TV1: INTERNAL_DAC2
[ 4.806473] rtl8192cu: MAC address: xx:xx:xx:xx:xx:xx
[ 4.806482] rtl8192cu: Board Type 0
[ 4.806718] rtlwifi: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 4.806760] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw.bin
[ 4.806807] usbcore: registered new interface driver rtl8192cu
[ 4.832056] intel8x0_measure_ac97_clock: measured 52277 usecs (2568 samples)
[ 4.832064] intel8x0: clocking to 46903
[ 4.898520] [drm] fb mappable at 0xC00C0000
[ 4.898526] [drm] vram apper at 0xC0000000
[ 4.898528] [drm] size 3145728
[ 4.898529] [drm] fb depth is 24
[ 4.898531] [drm] pitch is 4096
[ 4.904094] fbcon: radeondrmfb (fb0) is primary device
[ 5.016136] firewire_core 0000:05:02.0: created device fw0: GUID 0011d800003b972b, S400
[ 5.034062] ieee80211 phy0: Selected rate control algorithm 'rtl_rc'
[ 5.035222] rtlwifi: wireless switch is on
[ 5.118561] [drm] crtc 1 is connected to a TV
[ 5.276049] Console: switching to colour frame buffer device 100x37
[ 5.279220] radeon 0000:01:00.0: fb0: radeondrmfb frame buffer device
[ 5.279223] radeon 0000:01:00.0: registered panic notifier
[ 5.279232] [drm] Initialized radeon 2.33.0 20080528 for 0000:01:00.0 on minor 0
[ 5.737236] ppdev: user-space parallel port driver
[ 5.972543] [drm] not detecting due to 00000004
[ 5.975966] [drm] not detecting due to 00000004
[ 6.047466] [drm] not detecting due to 00000004
[ 6.049728] [drm] not detecting due to 00000004
[ 6.503355] [drm] crtc 1 is connected to a TV
[ 6.901993] 8139too 0000:05:03.0 eth0: link down
[ 6.911844] rtl8192cu: MAC auto ON okay!
[ 6.944723] rtl8192cu: Tx queue select: 0x05
[ 12.333954] [drm] not detecting due to 00000004
[ 12.335021] [drm] not detecting due to 00000004
[ 13.476033] [drm] not detecting due to 00000004
[ 13.477106] [drm] not detecting due to 00000004
[ 281.216185] usb 1-6: USB disconnect, device number 3
[ 281.228038] rtlwifi: reg 0x102, usbctrl_vendorreq TimeOut! status:0xffffffed value=0x400d0101
[ 281.228050] rtlwifi: reg 0x422, usbctrl_vendorreq TimeOut! status:0xffffffed value=0x90e1317
[ 281.228059] rtlwifi: reg 0x542, usbctrl_vendorreq TimeOut! status:0xffffffed value=0xf0002a0e
[ 281.228070] rtlwifi: reg 0x608, usbctrl_vendorreq TimeOut! status:0xffffffed value=0x0
[ 285.128040] usb 1-6: new high-speed USB device number 4 using ehci-pci
[ 285.262319] rtl8192cu: Chip version 0x10
[ 285.338891] rtl8192cu: MAC address: xx:xx:xx:xx:xx:xx
[ 285.338900] rtl8192cu: Board Type 0
[ 285.339132] rtlwifi: rx_max_size 15360, rx_urb_num 8, in_ep 1
[ 285.339192] rtl8192cu: Loading firmware rtlwifi/rtl8192cufw.bin
[ 285.339473] ieee80211 phy1: Selected rate control algorithm 'rtl_rc'
[ 285.345738] rtlwifi: wireless switch is on
[ 285.353759] rtl8192cu: MAC auto ON okay!
[ 285.388769] rtl8192cu: Tx queue select: 0x05


il router e configurato cosi:
dhcp attivo

Rete Wi-Fi (SSID) ********** (Nascosto)
Stato Interfaccia Radio Abilitato
Canale 6
Modalità di cifratura WPA-PSK AES 256 bit
Chiave di cifratura ********************** [ASCII]
Controllo Accesso Abilitato

[sacarde]

sembra tutto a posto


che vedi da: iwlist wlan0 scan


p.s.
come testi se funziona?

p.s.
hai provato da un'altra distro o live se da li funziona ?

[asghan]

lo stesso computer con la stessa scheda wifi su debian configurata con la gui wicd-kde (credo??) funziona perfettamente

iwlist wlan0 scan
wlan0 Scan completed :
Cell 01 - Address: xx:xx:xx:xx:xx:xx
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=70/70 Signal level=-39 dBm
Encryption key:on
ESSID:""
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=00000***********
Extra: Last beacon: 364ms ago
IE: Unknown: 00*********00000000000000000000000
IE: Unknown: ************************
IE: Unknown: ********
IE: Unknown: ************
IE: Unknown: **********
IE: Unknown: ********
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: Unknown: ***********
IE: Unknown: **********************
IE: Unknown: ************************
IE: WPA Version 1
Group Cipher : CCMP
Pairwise Ciphers (1) : CCMP
Authentication Suites (1) : PSK
IE: Unknown: ************************************************



non ho molta esperienza con il wifi, o usato
iwconfig wlan0
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry long limit:7 RTS thr=2347 B Fragment thr:off
Encryption key:off
Power Management:off

tramite il router verificando chi era connesso

e questo su geexbox (vedi img)


avrei provato anche tramite schell oppure script ma non conosco i comandi per fare la connessione manualmente

[sacarde]

- provato a riavviare il servizio di rete e controllare i log ?

se ho capito usa systemd, per avviare il servizio

sudo systemctl restart connman



per vedere errori:

sudo systemctl status connman





p.s.
manualmente dovrebbe essere:
iwconfig wlan0 essid apname key s:......
ifconfig wlan0 192.168.1.200 netmask 255.255.255.0 up
route add default gw 192.168.1.1
mettere in /etc/resolv.conf i dns


p.s.
non hai modo di installarci wicd?

[asghan]

ciao
ho provato a modificare le impostazioni
con
Modalità di cifratura WEP 128 bit
e rete visibile si collega in wifi

invece non si collega quando uso
Modalità di cifratura WPA-PSK AES 256 bit
e modificando solo questo su geexbox in /etc/network
SECURITY="PSK"
PASSPHRASE="xxxxxxxxxxxxxxx"

visto il risultato credo sia il router a non concedere l autorizzazione anche se non ho capito perche :confused: :muro:

e da ciò che letto il wep non mi sembra molto sicuro per collegmenti prolungati

in /var/log c'e solo questo
/var/log/Xorg.0.log
(e non mi sembra avere informazioni utili per la rete)


appena avviato il sitema e cosi

systemctl status connman
connman.service - Connection service
Loaded: loaded (/lib/systemd/system/connman.service; disabled)
Active: active (running) since mer 2013-11-27 03:23:19 UTC; 1min 6s ago
Process: 351 ExecStartPre=/usr/lib/connman/connman-parse-configuration2 (code=exited, status=0/SUCCESS)
Process: 242 ExecStartPre=/usr/lib/connman/connman-parse-configuration (code=exited, status=0/SUCCESS)
Main PID: 449 (connmand)
CGroup: /system.slice/connman.service
└─449 /usr/sbin/connmand -n

nov 27 03:23:20 geexbox connmand[449]: connmand[449]: wlan0 {update} flags 4099 <UP>
nov 27 03:23:20 geexbox connmand[449]: connmand[449]: wlan0 {newlink} index 3 address xx:xx:xx:xx:xx:xx mtu 1500
nov 27 03:23:20 geexbox connmand[449]: connmand[449]: wlan0 {newlink} index 3 operstate 5 <DORMANT>
nov 27 03:23:20 geexbox connmand[449]: wlan0 {update} flags 4099 <UP>
nov 27 03:23:20 geexbox connmand[449]: wlan0 {newlink} index 3 address xx:xx:xx:xx:xx:xx mtu 1500
nov 27 03:23:20 geexbox connmand[449]: wlan0 {newlink} index 3 operstate 5 <DORMANT>
nov 27 03:23:20 geexbox connmand[449]: connmand[449]: wlan0 {newlink} index 3 address xx:xx:xx:xx:xx:xx mtu 1500
nov 27 03:23:20 geexbox connmand[449]: connmand[449]: wlan0 {newlink} index 3 operstate 2 <DOWN>
nov 27 03:23:20 geexbox connmand[449]: wlan0 {newlink} index 3 address xx:xx:xx:xx:xx:xx mtu 1500
nov 27 03:23:20 geexbox connmand[449]: wlan0 {newlink} index 3 operstate 2 <DOWN>

---------------------------------------
ifconfig

eth0 Link encap:Ethernet HWaddr yy:yy:yy:yy:yy:yy
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:56 errors:0 dropped:0 overruns:0 frame:0
TX packets:56 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3384 (3.3 KiB) TX bytes:3384 (3.3 KiB)

wlan0 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)


---------------------------------------
iwconfig

wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry long limit:7 RTS thr=2347 B Fragment thr:off
Encryption key:off
Power Management:off


cat /etc/resolv.conf

# Generated by Connection Manager
nameserver 127.0.0.1


ho provato manualmente

systemctl stop connman.service

systemctl restart connman

systemctl status connman

con password in [ASCII] ottengo

iwconfig wlan0 essid xxxxxx key s:xxxxxxxxxxxxxxx
Error for wireless request "Set ESSID" (8B2A) :
SET failed on device wlan0 ; Invalid argument.


questo non da errori ma non risolve
iwconfig wlan0 essid xxxxxxx key restricted:xxxxxxxxxxxx


ifconfig wlan0 192.168.1.200 netmask 255.255.255.0 up
route add default gw 192.168.1.1
echo "nameserver 127.0.0.1" >> /etc/resolv.conf
echo "nameserver 192.168.1.1" >> /etc/resolv.conf



in conclusione non si collega ed ottengo questo


connman.service - Connection service
Loaded: loaded (/lib/systemd/system/connman.service; disabled)
Active: active (running) since mer 2013-11-27 03:24:26 UTC; 30s ago
Process: 792 ExecStartPre=/usr/lib/connman/connman-parse-configuration2 (code=exited, status=0/SUCCESS)
Process: 742 ExecStartPre=/usr/lib/connman/connman-parse-configuration (code=exited, status=0/SUCCESS)
Main PID: 845 (connmand)
CGroup: /system.slice/connman.service
└─845 /usr/sbin/connmand -n

nov 27 03:24:26 geexbox connmand[845]: eth0 {newlink} index 2 operstate 2 <DOWN>
nov 27 03:24:26 geexbox connmand[845]: wlan0 {update} flags 4099 <UP>
nov 27 03:24:26 geexbox connmand[845]: wlan0 {newlink} index 3 address xx:xx:xx:xx:xx:xx mtu 1500
nov 27 03:24:26 geexbox connmand[845]: wlan0 {newlink} index 3 operstate 2 <DOWN>
nov 27 03:24:36 geexbox connmand[845]: connmand[845]: wlan0 {add} address 192.168.1.103/24 label wlan0 family 2
nov 27 03:24:36 geexbox connmand[845]: wlan0 {add} address 192.168.1.103/24 label wlan0 family 2
nov 27 03:24:36 geexbox connmand[845]: connmand[845]: wlan0 {add} route 192.168.1.0 gw 0.0.0.0 scope 253 <LINK>
nov 27 03:24:36 geexbox connmand[845]: wlan0 {add} route 192.168.1.0 gw 0.0.0.0 scope 253 <LINK>
nov 27 03:24:46 geexbox connmand[845]: connmand[845]: wlan0 {add} route 0.0.0.0 gw 192.168.1.1 scope 0 <UNIVERSE>
nov 27 03:24:46 geexbox connmand[845]: wlan0 {add} route 0.0.0.0 gw 192.168.1.1 scope 0 <UNIVERSE>
---------------------------------------
eth0 Link encap:Ethernet HWaddr yy:yy:yy:yy:yy:yy
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:56 errors:0 dropped:0 overruns:0 frame:0
TX packets:56 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:3384 (3.3 KiB) TX bytes:3384 (3.3 KiB)

wlan0 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx
inet addr:192.168.1.200 Bcast:192.168.1.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

---------------------------------------
wlan0 IEEE 802.11bgn ESSID:"routerWifi"
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry long limit:7 RTS thr=2347 B Fragment thr:off
Encryption key:off
Power Management:off

---------------------------------------
# Generated by Connection Manager
nameserver 127.0.0.1
nameserver 127.0.0.1
nameserver 192.168.1.1
---------------------------------------



da cio che ho letto usa file *.opk
http://download.geexbox.org/releases/extra/i386/RTL8188CUS_v3.0.2164.20110715-1_i686.opk

opkg install wicd wicd-curses nano
Package nano (2.2.6-1) installed in root is up to date.
Collected errors:
* opkg_install_cmd: Cannot install package wicd.
* opkg_install_cmd: Cannot install package wicd-curses.

forse visto che posso usarlo da shell è piu adatto wicd-curses ma non è presente nessuno dei due
e non trovo nemmeno i file *.opk

per farlo manualmente temo siano tante le dipendenze da risolvere

ho provato a copiare wicd-curses in modo "improprio"
ma quando lo avvio
Could not find platform independent library <prefix>
consider setting $pythonhome to <prefix>[:<exec_prefix>]
ImportEror: NO module named site

[sacarde]

non hai log in /var/log ?

forse devi avviarli, che vedi riguardo a "log" da: systemctl list-unit-files


per testare la rete hai provato a fare un ping al router?
o a un indirizzo numerico es.: 173.194.35.120


p.s.
per installare pacchetti se non puoi usare una ethernet
li devi scaricare e copiare localmente

[asghan]

non so come si avviano i log
ho prato ad attivare il debugging ma poi non so dove o cosa cercare
ho prova attivare il debub
# ls /var/log
Xorg.0.log
Xorg.0.log.old


# systemctl list-unit-files
UNIT FILE STATE
dev-hugepages.mount static
dev-mqueue.mount static
sys-fs-fuse-connections.mount static
sys-kernel-config.mount static
sys-kernel-debug.mount static
tmp.mount static
systemd-ask-password-console.path static
systemd-ask-password-wall.path static
acpid.service disabled
automountd.service disabled
autovt@.service disabled
avahi-daemon.service disabled
avahi-dnsconfd.service disabled
bftpd-config.service disabled
bftpd.service disabled
bluetooth.service disabled
connman.service disabled
console-getty.service disabled
console-shell.service disabled
crond.service disabled
dbus-org.freedesktop.machine1.service static
dbus.service static
debug-shell.service disabled
display-manager.service masked
emergency.service static
getty@.service enabled
hwclock-sync.service masked
initrd-cleanup.service static
initrd-parse-etc.service static
initrd-switch-root.service static
initrd-udevadm-cleanup-db.service static
installator.service disabled
kmod-static-nodes.service static
lircd.service disabled
lspci.service disabled
mixer.service disabled
mpd.service disabled
network-link.service disabled
ntpd.service disabled
pvr.service disabled
quotaon.service static
rescue.service static
serial-getty@.service static
silent.service disabled
systemd-ask-password-console.service static
systemd-ask-password-wall.service static
systemd-fsck-root.service static
systemd-fsck@.service static
systemd-halt.service static
systemd-hibernate.service static
systemd-hybrid-sleep.service static
systemd-initctl.service static
systemd-journal-flush.service static
systemd-journald.service static
systemd-kexec.service static
systemd-machined.service static
systemd-modules-load.service static
systemd-nspawn@.service static
systemd-poweroff.service static
systemd-random-seed.service static
systemd-reboot.service static
systemd-remount-fs.service static
systemd-shutdownd.service static
systemd-suspend.service static
systemd-sysctl.service static
systemd-tmpfiles-clean.service static
systemd-tmpfiles-setup-dev.service static
systemd-tmpfiles-setup.service static
systemd-udev-settle.service static
systemd-udev-trigger.service static
systemd-udevd.service static
telnetd@.service static
tvheadend.service disabled
udhcpc.service disabled
udisks.service static
user@.service static
vdr.service disabled
video-card.service disabled
wpa_supplicant.service disabled
xbmc-setup.service disabled
xbmc.service disabled
xorg.service disabled
-.slice static
machine.slice static
system.slice static
avahi-daemon.socket disabled
dbus.socket static
syslog.socket static
systemd-initctl.socket static
systemd-journald.socket static
systemd-shutdownd.socket static
systemd-udevd-control.socket static
systemd-udevd-kernel.socket static
telnetd.socket disabled
basic.target static
bluetooth.target static
ctrl-alt-del.target disabled
default.target enabled
emergency.target static
final.target static
getty.target static
graphical.target disabled
halt.target disabled
hibernate.target static
hybrid-sleep.target static
initrd-fs.target static
initrd-root-fs.target static
initrd-switch-root.target static
initrd.target static
installator.target static
kexec.target disabled
local-fs-pre.target static
local-fs.target static
multi-user.target disabled
network-online.target static
network.target static
nss-lookup.target static
nss-user-lookup.target static
paths.target static
poweroff.target disabled
printer.target static
reboot.target disabled
remote-fs-pre.target static
remote-fs.target enabled
rescue.target disabled
rpcbind.target static
shutdown.target static
sigpwr.target static
sleep.target static
slices.target static
smartcard.target static
sockets.target static
sound.target static
suspend.target static
swap.target static
sysinit.target static
system-update.target static
time-sync.target static
timers.target static
umount.target static
xbmc.target enabled
systemd-tmpfiles-clean.timer static

142 unit files listed.




con il ping non ottengo alcuna risposta

la lan non sarebbe un problema, momentaneamente posso spostare il computer

solo che non ho trovato i binari *.opk che mi servono
e mon ho molta esperienza con i sorgenti e risolvere le varie dipendenze

[sacarde]

se hai la possibilita' di metterlo in rete con la ethernet

per gestire i pacchetti:

(aggiorna gli indici)
opkg update

(installa pacchetti, penso gestendo le dipendenze)
opkg install pkg_name


(rimuove pacchetti)
opkg remove pkg_name



p.s.
http://www.geexbox.org/geexbox-advanced-configuration-login-and-administration/

[asghan]

ciao :)
avevo provato ma...
# opkg install wicd
Collected errors:
* opkg_install_cmd: Cannot install package wicd.


purtroppo i Repository non contiene i binari che mi servono (http://download.geexbox.org/binaries/i386/latest/packages/)

cat /etc/opkg/opkg.conf
src snapshots http://download.geexbox.org/binaries/i386/latest/packages/
dest root /
lists_dir ext /var/lib/opkg/
option force_space

[sacarde]

eh si.... sembra proprio cosi'... i pacchetti sono molto limitati



p.s.
c'e' una cosa che non mi torna, che il servizio:

connman.service

appare "disabled"

andrebbe abilitato (systemctl enable connman.service)
avviato (systemctl start connman.service)
e visto gli errori eventuali (systemctl status connman.service)



p.s.
gli errori (se no si trova il log) si possono vedere nel log di systemd:
journalctl -b


p.s.
errore simile: http://www.geexbox.org/forum/topic/how-do-i-start-to-solve-wifi-problem/

[sacarde]

su irc.freenode.net c'e' un canale #geexbox
dove danno aiuto

o sul forum relativo
http://www.geexbox.org/forum

[asghan]

ciao

sul forum geexbox (se ho tradotto bene) avevo letto di problema simile al mio dove lo sfortunato utilizzatore aveva rinunciato a risolvere (pero usava una versione più vecchia)

a causa di imprevisti
per adesso sospendo tutto per qualche settimana

grazie :)